Rowenta Steamer Not Steaming

We all have electrical gadgets that we rely on because they make our lives easier when they’re working properly, but when they break down and you can’t figure out what’s wrong or why they stopped working, you tend to feel helpless. Particularly if you need to use them urgently and you’re clueless about how to fix them.

Rowenta steamers, like other technological appliances, are convenient since they keep our clothes fresh for outings and special occasions, but you don’t have to feel helpless if they break down or stop steaming.

There are simple troubleshooting techniques that can help you figure out what’s wrong and fix it.

Rowenta steamers that aren’t steaming can be rectified by removing mineral deposits, replacing the fuse, or straightening a bent steam hose.

Rowenta Steamer Not Steaming

You May Like

Shark Steam Mop Not Steaming
Can You Use a Clothes Steamer to Remove Wallpaper

Why Your Steamer Is Not Steaming & How to Solve the Issue

Some of the most common reasons Rowenta steamers stop streaming are as follows:

Mineral deposits have clogged the steamer.

Minerals can be found in water in many forms.

A coating of mineral deposit will build on the steamer if a mineral such as calcium emits from the water. This mineral buildup will make it difficult for steam to escape.

If a Rowenta steamer becomes clogged with mineral deposits, it will likely stop producing steam.

To fix this is easy, you only need to decalcify (remove the calcium) the steamer if you realize it isn’t creating steam. 

It’s simple to do: mix a solution of one part vinegar to two parts distilled water and pour it into the reservoir of your steamer. Allow it to cool before emptying the steamer. Repeat until the mineral deposits have vanished. You don’t need to use your apple cider vinegar for this solution; white vinegar will suffice.

In addition, if the steam comes out in intermittent gushes, researching the problem may reveal a white buildup inside the steamer.

The white deposit is limescale, which is caused by the minerals in the water being released after it has been steamed. On the inside of your steamer, these minerals build-up and leave a residue.

So, how can you get rid of the sediments and limescale in your steamer?

Disconnect the hose, pole, and other attachments in the steamer to remove the limescale and sediments and flush the steamer inside out by placing it in a large sink or bath, unscrewing the little drainage valve.

Fill this little drainage valve with water until it runs clear.

Power Socket That Isn’t Working

The loss of power is another reason the Rowenta steamer isn’t steaming.

There could be an issue with the power socket. If your steamer does not turn on at all,

it’s possible that a fuse blew, causing the circuit breaker to cut the power.

Check to ensure that the circuit breaker box is in good operating order.

If the breaker is operating properly, it’s possible that the plug isn’t fully inserted into the wall, or that the prongs of your steamer plugs are bent to angles that don’t fit – neither of which is a cause for concern. You can return them to their original position by adjusting them.

If everything else fails, there’s a potential your plug’s prongs have corroded, so when you notice this is the case, the next step is to replace the plug.

What happens if the steamer doesn’t heat up?

When you turn on a Rowenta steamer, it’s usually ready to use. They take 45 seconds to a minute to heat up to the point where the water can steam properly. So, if you notice it doesn’t heat up, don’t panic; your steamer is still functional.

Most garment steamers have an indicator light that illuminates while they are heating up and turns off after they are fully heated.  

Pay attention to these indicator lights if your steamer has them. Your garment steamer should be hot and ready to use after the light turns off.

If it does not heat up and the indicator light does not illuminate, the problem could be with the power socket.

A steam hose that is faulty or has become dislodged

Your steamer may be making unusual gurgling noises, and you may notice condensation droplets forming on the steamer’s head.

These indicators indicate that a problem with the steam hose inside the steamer may exist. It’s possible that the steam hose has been distorted, preventing steam from flowing properly.

If you have a vertical garment steamer set down horizontally or a horizontal steamer that you keep up vertically, the steam hose can get bent, so be careful.

To fix the problem with your steam hose, locate it and elevate it so that it is not bent in any way. When you do this, the condensation will be permitted to circulate.

Tips to Improve the Performance of Your Rowenta Steamer

Here are some suggestions for keeping the Rowenta steamer in good working order before and after use:

  1. When using a Rowenta steamer, make sure to use filtered water. The steamer will not become clogged as a result of this procedure.
  1. Ensure that the steaming hose is straight. Check to see if the hose is twisted or crinkled as well.
  1. Do not let your steamer’s water sit for more than 30 days. Drain it at all times. It’s possible that sediments will form if you don’t.
  1. Clean your steamer with a solution of equal parts vinegar and distilled water every 45-60 days to prevent mineral accumulation and keep it clean.
  1. To avoid water spots and buildup, wipe to clean your steamer after each usage with a damp towel.


When your Rowenta steamer begins to malfunction, you may become concerned.

Even so, you don’t have to throw it away or buy a new one right away because the problem could be caused by something as simple as a defective plug, a bent hose, or a buildup of mineral deposits.

You can avoid worrying or spending extra money on a new steamer if you use the troubleshooting methods described above.

Always remember to take proper care of the steamer in order to keep troubles to a minimum; this will allow it to last longer.

Leave a Comment

Your email address will not be published.